產品特點 Product Features

精致的制作工藝和合理的結構使母線表面精致大方，達到箱內箱外無積水要求。在必要的母線底板上有集水槽，在集水槽的端部設有集水自動放棄裝置。既能有效地放棄母線內部積水，又能阻擋灰塵及異物的進入。

高壓封閉共箱母線總體直線長度超過40m，或者是穿越建筑結構中的伸縮縫，采用伸縮節，它主要是實現水平、垂直方向兩個自由度的調節，不僅能滿足不同溫降及熱漲冷縮引起的伸縮要求。還可以對基礎沉降所引起的誤差進行補償。其的伸縮節設計，使較大的母線箱體能夠靈活拼接，從而使母線系統的設計、安裝能夠達到程序化、標準化。

The exquisite production process and reasonable structure make the surface of the busbar exquisite and generous, achieving the requirement of no water accumulation inside and outside the box. There is a water collection tank on the necessary busbar base plate, and an automatic water collection abandonment device is installed at the end of the water collection tank. It can effectively eliminate the accumulation of water inside the busbar and block the entry of dust and foreign objects.

The overall straight length of the high-voltage enclosed common box busbar exceeds 40m, or it passes through expansion joints in building structures. Expansion joints are used to adjust the two degrees of freedom in the horizontal and vertical directions, which can not only meet the expansion requirements caused by different temperature drops and thermal expansion and contraction. It is also possible to compensate for errors caused by foundation settlement. Its special expansion joint design enables flexible splicing of larger busbar boxes, thereby achieving programmatic and standardized design and installation of busbar systems.

產品概述 Product Overview

GFM 高壓共箱母線槽主要適用于額定電壓6kV、10kV、20kV、35kV 高壓配電盤與變壓器之間的電氣連接，例如: 大型廠礦的供電系統、大型變電站、大型企業的自備電廠、大型建筑及發電機至升壓變壓器之間的電氣連接。

該產品采用分相式結構，每相有絕緣及合金外殼，絕緣性能、安全電壓符合標準要求。因三相分隔在空氣中，具有三相電壓均衡、溫升低、載流能力大、安裝方便等特點。

母線槽全程設智能監控裝置，系統運行狀況盡在掌握中，供電系統安全運行。母線槽自帶測控線槽，安裝便捷。

高壓共箱母線槽兩側為散熱器式的鋁鎂合金型材，厚度達到3.0mm，由于散熱條亦可增強側板鋼性強度，因此兩側高度可達到305mm 高度亦可無須任何加強措施。上下封板采用敷鋁鋅板，亦是保證組裝成型后母線整體的結構強度。側板與底板采用高強度

鉚釘鉚緊。蓋板與兩側板則用螺栓連接。每節母線一般在上部都合理的設有標準檢修孔( 也可根據現場需求側面設置)，檢修口處的制作工藝和高要求的伸縮節連接技術，使母線外殼防護等級高達IP54。

GFM high-voltage common box bus duct is mainly suitable for electrical connection between rated voltage 6kV, 10kV, 20kV, 35kV high-voltage distribution panels and transformers, such as power supply systems in large factories and mines, large substations, self owned power plants of large enterprises, electrical connections between large buildings and generators and step-up transformers.

This product adopts a phase separated structure, with insulation and alloy shell for each phase, and the insulation performance and safety voltage meet the standard requirements. Due to the three- phase separation in the air, it has the characteristics of balanced three-phase voltage, low temperature rise, high current carrying capacity, and easy installation.

The bus duct is equipped with intelligent monitoring devices throughout the entire process, and the system operation status is under control to ensure the safe operation of the power supply system. The bus duct comes with a built-in measurement and control cable duct, making installation convenient.

This product adopts a phase separated structure, with insulation and alloy shell for each phase, and the insulation performance and safety voltage meet the standard requirements. Due to the three-phase separation in the air, it has the characteristics of balanced three-phase voltage, low temperature rise, high current carrying capacity, and easy installation.

The two sides of the high-voltage common box bus duct are radiator type aluminum magnesium alloy profiles with a thickness of 3.0mm. As the heat dissipation strip can also enhance the steel strength of the side plate, the height on both sides can reach 305mm without any reinforcement measures. The upper and lower sealing plates are made of aluminum zinc coated plates to ensure the overall structural strength of the assembled busbar. The side panel and bottom panel are fastened with high-strength imported rivets. The cover plate and the two side plates are connected by bolts. Each section of the busbar is generally equipped with standard maintenance holes at the upper part (which can also be set on the side according to on-site requirements). The unique manufacturing process and high demand expansion joint connection technology at the maintenance hole make the protection level of the busbar shell as high as IP54.

技術參數 Technical Parameter

額定工頻干試耐受電壓(1min )、額定( 雷電 ) 沖擊耐受電壓、額定工作電壓、工作電壓。

Rated power frequency dry test withstand voltage (1 minute), rated (lightning) impulse withstand voltage, rated operating voltage, and maximum operating voltage.